Jimmys Auto Blog

Electricity is the lifeline of the car. This has always been the case since almost all the gasoline ignited combustion using electricity to the fuel. Today, the entire automobile is controlled and operated the electricity and electronic devices. These include controlling fuel, emission controls, accessories, such as heating and air conditioning, steering, brakes, lights and much more. It is obvious that the charging scheme, that this current is supplied to a very important System.

The charging system usually include a method to generate electricity and store a battery for power. This sounds easy, but it is no longer a simple system. The typical system consists of a generator, which normally belt driven by the engine. The generator of this park must be regulated to control the voltage with in a given area. The usual is 12 volts to about 14.2 volts. If the voltage is too high or too low electronic and electrical components will not work or they can be damaged.

Each generator is a form of electronic controller that controls the output of the generator. In recent years, it was a regulator mounted in the vehicle regardless of the alternator. A few years ago the regulator was moved into the alternator and the system was known internally regulated. A few manufacturers decided that the electrical system should be using the computer network interface. Now most cars either the charging system is a computer or monitor and there are certain levels by the engine management computer. Many systems reduce the alternator load during periods of strong acceleration.

Can I test and diagnose problems with my generator? It depends on the equipment you have. A good multimeter will receive a fair overview of the state of a charging system. If all you have is a multi-meter to measure the voltage at the battery terminals before starting the engine. Then you measure the voltage with thethe engine is running on a fast idle. The resting tension was in the vicinity of 12.6 volts and the voltage typically ranges from 13.2 to 14.2 volts at the battery. You can also measure the output voltage of the alternator, and it should be the measure in the 0.1 volt battery voltage. After measuring the voltage at a fast idle, turn off all accessories and lights. The tension should be near the same as for a fast idle with about 3 or 4 tenths volts.

Read more…

I'm eager to hear your comments...

Indeed, it is fulfilling for car owners to change the entire working condition of his car. But changing your old stereo with a new one is more rewarding than any other tough jobs. It is like the cream of the crop.

Here, you’ll be needing your newly bought car stereo, wiring kits for adapters, wire crimping tools, tape, cutters, screwdriver/s. The features of your new stereo will depend on your choice, personality, or the whole environment of your car.

Use a wiring kit to save you an hour from your installing time, minus the frustrations.

You have to first remove the trim panels then remove the trim around the stereo. Some cars have a lot of panels to get to the stereo itself. These panels are always attached by screws. Some as visible and others need proper focus to see it. Either way, you have to carefully remove these and put them in some place where you can easily find it. Do not lose something as important as these.

We go to the portion where you remove the stereo from its nesting point. With everything out, all you need to do is carefully detach your old stereo. Again, this would be held by numerous screws so get your screwdrivers ready. After successfully getting it out, don’t just plug the new one in. There are still tasks you have to accomplish like connecting the wires altogether with the harness.

Alright, now here’s the hard part. For you to connect the adapter, you have to crimp its connections by stripping the wires. Do not try installing a stereo with only electrical tape to connect it, like twisting it together. Refer to the manual provided with the stereo. Now that you have it done, you can plug the adapter into the harness and do a test run. If all seems okay, you can now re-install all those panels that you just detached.

Finish your installation by securing your new stereo into the dashboard bracket. Arrange the electrical wirings back in its place. Then safely push your stereo back into the area. All done! Now you can enjoy a more convenient way of listening to your music.

Article sponsored by: www.jimmysautoservices.com

What do you think? Please comment below to tell me.